Dominator Octane Boost (AOB)
Gasoline Stabilizer (AST)
P.I Performance Improver (API)
5W-30 Signature Series Synthetic Motor Oil (ASL)
5W-30 Extended Life Synthetic Motor Oil (XLF)
5W-30 OE Series Synthetic Motor Oil (OEF)
Signature Series Fuel-Efficient Synthetic ATF
OE Series Fuel-Efficient Synthetic ATF
DOT 3 and 4 Synthetic Brake Fluid (BFLV)
Passenger Vehicle Antifreeze (ANTPC)
Antifreeze and Engine Coolant (ANT)
MANN-FILTERS Oil FiltersMaintenance Schedule as Provided by OEM Documentation
| Distance: 7,500 miles (12,000 km) | Action: Inspect/replace | Item: Brake pads | Interval in Month(s): | Labor Units: 0.3 | Parts Units: 0 | Drive Type: ALL |
| Description: High-friction material attached to a metal backing plate. | ||||||
| Distance: 7,500 miles (12,000 km) | Action: Inspect | Item: Coolant | Interval in Month(s): 12 | Labor Units: 0.05 | Parts Units: 0 | Drive Type: ALL |
| Description: Also known as "antifreeze." A mixture of water and ethylene glycol that has both a higher boiling point and a lower freezing point than plain water. | ||||||
| Distance: 7,500 miles (12,000 km) | Action: Inspect & adjust air pressure | Item: Wheels & tires | Interval in Month(s): 12 | Labor Units: 0.1 | Parts Units: 0 | Drive Type: ALL |
| Description: A circular frame of hard material that may be solid or partly solid, is capable of turning on an axle, and holds the rubber cushion that contains compressed air. | ||||||
| Distance: 7,500 miles (12,000 km) | Action: Reset | Item: Service reminder light | Interval in Month(s): 12 | Labor Units: 0.1 | Parts Units: 0 | Drive Type: ALL |
| Description: A light that indicates that general vehicle maintenance is needed or that a specific service is required. | ||||||
| Distance: 7,500 miles (12,000 km) | Action: Check level | Item: Power steering fluid | Interval in Month(s): 24 | Labor Units: 0.02 | Parts Units: 0 | Drive Type: ALL |
| Description: Hydraulic fluid used in a power steering system. | ||||||
| Distance: 7,500 miles (12,000 km) | Action: Inspect | Item: Brake fluid | Interval in Month(s): 24 | Labor Units: 0.05 | Parts Units: 0 | Drive Type: ALL |
| Description: The fluid used in the hydraulic brake system. | ||||||
| Distance: 7,500 miles (12,000 km) | Action: Inspect | Item: Windshield wipers & washer | Interval in Month(s): 24 | Labor Units: 0.05 | Parts Units: 0 | Drive Type: ALL |
| Description: Motorized mechanical arms with rubber inserts used to wipe the windshield or back glass. A small pump and reservoir that can direct a jet of cleaning solution at the windshield or back glass. | ||||||
| Distance: 7,500 miles (12,000 km) | Action: Inspect/adjust | Item: On-board diagnosis system | Interval in Month(s): 24 | Labor Units: 0.05 | Parts Units: 0 | Drive Type: ALL |
| Description: A computer-controlled system that identifies malfunctioning or out-of-adjustment components under its control through the display of trouble codes. The presence of trouble codes is usually indicated by an intermittently or constantly lit "check engine " or "service engine soon" light. | ||||||
| Distance: 7,500 miles (12,000 km) | Action: Change | Item: Engine oil | Interval in Month(s): 12 | Labor Units: 0.31 | Parts Units: 7.8 | Drive Type: ALL |
| Description: A substance that lubricates and cools the moving parts of the engine and reduces corrosion and the formation of rust. | ||||||
| Distance: 7,500 miles (12,000 km) | Action: Replace | Item: Oil filter | Interval in Month(s): 12 | Labor Units: 0.1 | Parts Units: 1 | Drive Type: ALL |
| Description: A cartridge-filled canister placed in an engine's lubricating system to strain dirt and abrasive materials out of the oil. | ||||||
| Distance: 15,000 miles (24,000 km) | Action: Inspect/adjust | Item: Parking brake | Interval in Month(s): 24 | Labor Units: 0.05 | Parts Units: 0 | Drive Type: ALL |
| Description: The mechanical brake connected by cables to either a ratcheting hand lever or foot pedal used to hold or apply a vehicle's rear and sometimes front brakes while left unattended or under conditions of hydraulic circuit failure. Sometimes referred to as the emergency brake. | ||||||
| Distance: 15,000 miles (24,000 km) | Action: Inspect | Item: Bevel gear | Interval in Month(s): 132 | Labor
Units: 0.05 | Parts Units: 0 | Drive Type: ALL |
| Description: In differential drives, the bevel gear transmits power to two axles spinning at different speeds | ||||||
| Distance: 15,000 miles (24,000 km) | Action: Replace | Item: Cabin air filter | Interval in Month(s): 48 | Labor Units: 0.05 | Parts Units: 1 | Drive Type: ALL |
| Description: A filtering system that meters out pollen, road dust and other particles before they can reach the passenger cabin. | ||||||
| Distance: 30,000 miles (48,000 km) | Action: Inspect | Item: Battery | Interval in Month(s): 12 | Labor Units: 0.1 | Parts Units: 0 | Drive
Type: ALL |
| Description: A box containing lead plates filled with a water and acid mixture that stores electricity generated by the alternator. It is the source of power for parts of the car that operate on electricity. | ||||||
| Distance: 30,000 miles (48,000 km) | Action: Inspect | Item: Fuel lines & hoses | Interval in Month(s): 24 | Labor Units: 0.05 | Parts Units: 0 | Drive Type: ALL |
| Description: The tubing that carries fuel throughout a vehicle. | ||||||
| Distance: 30,000 miles (48,000 km) | Action: Inspect | Item: Brake lines, hoses & connections | Interval in Month(s): 48 | Labor Units: 0.3 | Parts Units: 0 | Drive
Type: ALL |
| Description: Tubes and their connections that carry brake fluid between the various components in a vehicle's brake system. | ||||||
| Distance: 37,500 miles (60,000 km) | Action: Replace | Item: Air filter | Interval in Month(s): 48 | Labor Units: 0.2 | Parts Units: 1 | Drive Type: ALL |
| Description: A device that filters incoming air fed to the engine. | ||||||
| Distance: 37,500 miles (60,000 km) | Action: Flush/replace | Item: Brake fluid | Interval in Month(s): 48 | Labor Units: 0.7 | Parts Units: 1 | Drive Type: ALL |
| Description: The fluid used in the hydraulic brake system. | ||||||
| Distance: 45,000 miles (72,000 km) | Action: Inspect | Item: Battery | Interval in Month(s): 12 | Labor Units: 0.1 | Parts Units: 0 | Drive Type: ALL |
| Description: A box containing lead plates filled with a water and acid mixture that stores electricity generated by the alternator. It is the source of power for parts of the car that operate on electricity. | ||||||
| Distance: 52,500 miles (84,000 km) | Action: Change | Item: Automatic transmission fluid | Interval in Month(s): 84 | Labor Units: 0.5 | Parts Units: 5.8 | Drive Type: ALL |
| Description: The fluid used for lubricating and cooling an automatic transmission. | ||||||
| Distance: 60,000 miles (96,000 km) | Action: Inspect | Item: Steering & suspension | Interval in Month(s): 96 | Labor Units: 0.25 | Parts Units: 0 | Drive Type: ALL |
| Description: A vehicle's steering is the collection of components that enable the operator to direct a vehicle in a desired direction. Suspension is the assemblage of joints, links and other components between a vehicle and its wheels. | ||||||
| Distance: 60,000 miles (96,000 km) | Action: Inspect boots & seals | Item: Drive shaft, pilot bearing & u-joints | Interval in Month(s): 144 | Labor Units: 0.2 | Parts Units: 0 | Drive Type: ALL |
| Description: In a rear- or four-wheel drive vehicle, the drive shaft is a sturdy metal tube with flexible joints on either end that connects the source of power to a differential. The pilot bearing is a bearing press-fit into the rear of the crankshaft that supports the tip of the transmission input shaft. It should be routinely replaced whenever the clutch is replaced as this is when it's most accessible. | ||||||
| Distance: 60,000 miles (96,000 km) | Action: Inspect | Item: Exhaust system | Interval in Month(s): 180 | Labor Units: 0.05 | Parts Units: 0 | Drive Type: ALL |
| Description: A system of tubing that routes exhaust gases from the exhaust manifold to the rear of the car and into the air. The exhaust system includes catalytic converters and mufflers that help reduce air and noise pollution generated by an engine. | ||||||
| Distance: 67,500 miles (108,000 km) | Action: Inspect boots & seals | Item: Drive shaft, pilot bearing & u-joints | Interval in Month(s): 120 | Labor Units: 0.2 | Parts Units: 0 | Drive Type: ALL |
| Description: In a rear- or four-wheel drive vehicle, the drive shaft is a sturdy metal tube with flexible joints on either end that connects the source of power to a differential. The pilot bearing is a bearing press-fit into the rear of the crankshaft that supports the tip of the transmission input shaft. It should be routinely replaced whenever the clutch is replaced as this is when it's most accessible. | ||||||
| Distance: 67,500 miles (108,000 km) | Action: Inspect | Item:
Steering & suspension | Interval in Month(s): 132 | Labor Units: 0.25 | Parts Units: 0 | Drive Type: ALL |
| Description: A vehicle's steering is the collection of components that enable the operator to direct a vehicle in a desired direction. Suspension is the assemblage of joints, links and other components between a vehicle and its wheels. | ||||||
| Distance: 67,500 miles (108,000 km) | Action: Inspect | Item: Exhaust system | Interval in Month(s): 156 | Labor Units: 0.05 | Parts Units: 0 | Drive Type: ALL |
| Description: A system of tubing that routes exhaust gases from the exhaust manifold to the rear of the car and into the air. The exhaust system includes catalytic converters and mufflers that help reduce air and noise pollution generated by an engine. | ||||||
| Distance: 75,000 miles (120,000 km) | Action: Inspect | Item: Battery | Interval in Month(s): 12 | Labor Units: 0.1 | Parts Units: 0 | Drive Type: ALL |
| Description: A box containing lead plates filled with a water and acid mixture that stores electricity generated by the alternator. It is the source of power for parts of the car that operate on electricity. | ||||||
| Distance: 75,000 miles (120,000 km) | Action: Inspect | Item: Steering & suspension | Interval in Month(s): 108 | Labor Units: 0.25 | Parts Units: 0 | Drive Type: ALL |
| Description: A vehicle's steering is the collection of components that enable the operator to direct a vehicle in a desired direction. Suspension is the assemblage of joints, links and other components between a vehicle and its wheels. | ||||||
| Distance: 75,000 miles (120,000 km) | Action: Inspect | Item: Exhaust system | Interval in Month(s): 120 | Labor Units: 0.05 | Parts Units: 0 | Drive Type: ALL |
| Description: A system of tubing that routes exhaust gases from the exhaust manifold to the rear of the car and into the air. The exhaust system includes catalytic converters and mufflers that help reduce air and noise pollution generated by an engine. | ||||||
| Distance: 75,000 miles (120,000 km) | Action: Inspect boots & seals | Item: Drive shaft, pilot bearing & u-joints | Interval in Month(s): 228 | Labor Units: 0.2 | Parts Units: 0 | Drive Type: ALL |
| Description: In a rear- or four-wheel drive vehicle, the drive shaft is a sturdy metal tube with flexible joints on either end that connects the source of power to a differential. The pilot bearing is a bearing press-fit into the rear of the crankshaft that supports the tip of the transmission input shaft. It should be routinely replaced whenever the clutch is replaced as this is when it's most accessible. | ||||||
| Distance: 75,000 miles (120,000 km) | Action: Replace | Item: Spark plugs | Interval in Month(s): 48 | Labor Units: 0.6 | Parts Units: 6 | Drive Type: ALL |
| Description: Cables that carry a high-voltage electrical charge from the distributor cap or ignition coils to the spark plugs. | ||||||
| Distance: 82,500 miles (132,000 km) | Action: Inspect | Item: Exhaust system | Interval in Month(s): 168 | Labor Units: 0.05 | Parts Units: 0 | Drive Type: ALL |
| Description: A system of tubing that routes exhaust gases from the exhaust manifold to the rear of the car and into the air. The exhaust system includes catalytic converters and mufflers that help reduce air and noise pollution generated by an engine. | ||||||
| Distance: 82,500 miles (132,000 km) | Action: Inspect boots & seals | Item: Drive shaft, pilot bearing & u-joints | Interval in Month(s): 168 | Labor Units: 0.2 | Parts Units: 0 |
Drive Type: ALL |
| Description: In a rear- or four-wheel drive vehicle, the drive shaft is a sturdy metal tube with flexible joints on either end that connects the source of power to a differential. The pilot bearing is a bearing press-fit into the rear of the crankshaft that supports the tip of the transmission input shaft. It should be routinely replaced whenever the clutch is replaced as this is when it's most accessible. | ||||||
| Distance: 82,500 miles (132,000 km) | Action: Inspect | Item: Steering & suspension | Interval in Month(s): 180 | Labor Units: 0.25 | Parts Units: 0 | Drive Type: ALL |
| Description: A vehicle's steering is the collection of components that enable the operator to direct a vehicle in a desired direction. Suspension is the assemblage of joints, links and other components between a vehicle and its wheels. | ||||||
| Distance: 90,000 miles (144,000 km) | Action: Inspect | Item: Steering & suspension | Interval in Month(s): 156 | Labor Units: 0.25 | Parts Units: 0 | Drive Type: ALL |
| Description: A vehicle's steering is the collection of components that enable the operator to direct a vehicle in a desired direction. Suspension is the assemblage of joints, links and other components between a vehicle and its wheels. | ||||||
| Distance: 90,000 miles (144,000 km) | Action: Inspect boots & seals | Item: Drive shaft, pilot bearing & u-joints | Interval in Month(s): 156 | Labor Units: 0.2 | Parts Units: 0 | Drive
Type: ALL |
| Description: In a rear- or four-wheel drive vehicle, the drive shaft is a sturdy metal tube with flexible joints on either end that connects the source of power to a differential. The pilot bearing is a bearing press-fit into the rear of the crankshaft that supports the tip of the transmission input shaft. It should be routinely replaced whenever the clutch is replaced as this is when it's most accessible. | ||||||
| Distance: 90,000 miles (144,000 km) | Action: Inspect | Item: Exhaust system | Interval in Month(s): 204 | Labor Units: 0.05 | Parts Units: 0 | Drive Type: ALL |
| Description: A system of tubing that routes exhaust gases from the exhaust manifold to the rear of the car and into the air. The exhaust system includes catalytic converters and mufflers that help reduce air and noise pollution generated by an engine. | ||||||
| Distance: 97,500 miles (156,000 km) | Action: Inspect | Item: Exhaust system | Interval in Month(s): 156 | Labor Units: 0.05 | Parts Units: 0 | Drive Type: ALL |
| Description: A system of tubing that routes exhaust gases from the exhaust manifold to the rear of the car and into the air. The exhaust system includes catalytic converters and mufflers that help reduce air and noise pollution generated by an engine. | ||||||
| Distance: 97,500 miles (156,000 km) | Action: Inspect boots & seals | Item: Drive shaft, pilot bearing & u-joints | Interval in Month(s): 192 | Labor Units: 0.2 | Parts Units: 0 |
Drive Type: ALL |
| Description: In a rear- or four-wheel drive vehicle, the drive shaft is a sturdy metal tube with flexible joints on either end that connects the source of power to a differential. The pilot bearing is a bearing press-fit into the rear of the crankshaft that supports the tip of the transmission input shaft. It should be routinely replaced whenever the clutch is replaced as this is when it's most accessible. | ||||||
| Distance: 97,500 miles (156,000 km) | Action: Inspect | Item: Steering & suspension | Interval in Month(s): 204 | Labor Units: 0.25 | Parts Units: 0 | Drive Type: ALL |
| Description: A vehicle's steering is the collection of components that enable the operator to direct a vehicle in a desired direction. Suspension is the assemblage of joints, links and other components between a vehicle and its wheels. | ||||||
| Distance: 105,000 miles (168,000 km) | Action: Inspect | Item: Battery | Interval in Month(s): 12 | Labor Units: 0.1 | Parts Units: 0 | Drive Type: ALL |
| Description: A box containing lead plates filled with a water and acid mixture that stores electricity generated by the alternator. It is the source of power for parts of the car that operate on electricity. | ||||||
| Distance: 105,000 miles (168,000 km) | Action: Inspect | Item: Exhaust system | Interval in Month(s): 132 | Labor Units: 0.05 | Parts Units: 0 | Drive Type: ALL |
| Description: A system of tubing that routes exhaust gases from the exhaust manifold to the rear of the car and into the air. The exhaust system includes catalytic converters and mufflers that help reduce air and noise pollution generated by an engine. | ||||||
| Distance: 105,000 miles (168,000 km) | Action: Inspect | Item: Steering & suspension | Interval in Month(s): 168 | Labor Units: 0.25 | Parts Units: 0 | Drive Type: ALL |
| Description: A vehicle's steering is the collection of components that enable the operator to direct a vehicle in a desired direction. Suspension is the assemblage of joints, links and other components between a vehicle and its wheels. | ||||||
| Distance: 105,000 miles (168,000 km) | Action: Inspect boots & seals | Item:
Drive shaft, pilot bearing & u-joints | Interval in Month(s): 240 | Labor Units: 0.2 | Parts Units: 0 | Drive Type: ALL |
| Description: In a rear- or four-wheel drive vehicle, the drive shaft is a sturdy metal tube with flexible joints on either end that connects the source of power to a differential. The pilot bearing is a bearing press-fit into the rear of the crankshaft that supports the tip of the transmission input shaft. It should be routinely replaced whenever the clutch is replaced as this is when it's most accessible. | ||||||
| Distance: 112,500 miles (180,000 km) | Action: Inspect boots & seals | Item: Drive shaft, pilot bearing & u-joints | Interval in Month(s): 108 | Labor Units: 0.2 | Parts Units: 0 | Drive Type: ALL |
| Description: In a rear- or four-wheel drive vehicle, the drive shaft is a sturdy metal tube with flexible joints on either end that connects the source of power to a differential. The pilot bearing is a bearing press-fit into the rear of the crankshaft that supports the tip of the transmission input shaft. It should be routinely replaced whenever the clutch is replaced as this is when it's most accessible. | ||||||
| Distance: 112,500 miles (180,000 km) | Action: Inspect | Item: Steering & suspension | Interval in Month(s): 144 | Labor Units: 0.25 | Parts Units: 0 | Drive Type: ALL |
| Description: A vehicle's steering is the collection of components that enable the operator to direct a vehicle in a desired direction. Suspension is the assemblage of joints, links and other components between a vehicle and its wheels. | ||||||
| Distance: 112,500 miles (180,000 km) | Action: Inspect | Item: Exhaust system | Interval in Month(s): 168 | Labor Units: 0.05 | Parts Units: 0 | Drive Type: ALL |
| Description: A system of tubing that routes exhaust gases from the exhaust manifold to the rear of the car and into the air. The exhaust system includes catalytic converters and mufflers that help reduce air and noise pollution generated by an engine. | ||||||
| Distance: 112,500 miles (180,000 km) | Action: Replace | Item: Serpentine belt | Interval in Month(s): 168 | Labor Units: 0.5 | Parts Units: 1 | Drive Type: ALL |
| Description: A ribbed drive belt that drives more than one engine accessory. | ||||||
| Distance: 120,000 miles (192,000 km) | Action: Replace | Item: Fuel filter | Interval in Month(s): | Labor Units: 0.6 | Parts Units: 1 | Drive Type: ALL |
| Description: A replaceable metal or plastic canister that prevents particulate matter and most contaminants in the fuel from reaching the engine. | ||||||
| Distance: 127,500 miles (204,000 km) | Action: Inspect boots & seals | Item: Drive shaft, pilot bearing & u-joints | Interval in Month(s): 96 | Labor Units: 0.2 | Parts Units: 0 | Drive Type: ALL |
| Description: In a rear- or four-wheel drive vehicle, the drive shaft is a sturdy metal tube with flexible joints on either end that connects the source of power to a differential. The pilot bearing is a bearing press-fit into the rear of the crankshaft that supports the tip of the transmission input shaft. It should be routinely replaced whenever the clutch is replaced as this is when it's most accessible. | ||||||
| Distance: 127,500 miles (204,000 km) | Action: Inspect | Item: Exhaust system | Interval in Month(s): 120 | Labor Units: 0.05 | Parts Units: 0 | Drive Type: ALL |
| Description: A system of tubing that routes exhaust gases from the exhaust manifold to the rear of the car and into the air. The exhaust system includes catalytic converters and mufflers that help reduce air and noise pollution generated by an engine. | ||||||
| Distance: 127,500 miles (204,000 km) | Action: Inspect | Item: Steering & suspension | Interval in Month(s): 192 | Labor Units: 0.25 | Parts Units: 0 | Drive Type: ALL |
| Description: A vehicle's steering is the collection of components that enable the operator to direct a vehicle in a desired direction. Suspension is the assemblage of joints, links and other components between a vehicle and its wheels. | ||||||
| Distance: 135,000 miles (216,000 km) | Action: Inspect | Item: Battery | Interval in Month(s): 12 | Labor Units: 0.1 | Parts Units: 0 | Drive Type: ALL |
| Description: A box containing lead plates filled with a water and acid mixture that stores electricity generated by the alternator. It is the source of power for parts of the car that operate on electricity. | ||||||
| Distance: 135,000 miles (216,000 km) | Action: Inspect | Item: Exhaust system | Interval in Month(s): 108 | Labor Units: 0.05 | Parts Units: 0 | Drive Type: ALL |
| Description: A system of tubing that routes exhaust gases from the exhaust manifold to the rear of the car and into the air. The exhaust system includes catalytic converters and mufflers that help reduce air and noise pollution generated by an engine. | ||||||
| Distance: 135,000 miles (216,000 km) | Action: Inspect boots & seals | Item: Drive shaft, pilot bearing & u-joints | Interval in Month(s):
180 | Labor Units: 0.2 | Parts Units: 0 | Drive Type: ALL |
| Description: In a rear- or four-wheel drive vehicle, the drive shaft is a sturdy metal tube with flexible joints on either end that connects the source of power to a differential. The pilot bearing is a bearing press-fit into the rear of the crankshaft that supports the tip of the transmission input shaft. It should be routinely replaced whenever the clutch is replaced as this is when it's most accessible. | ||||||
| Distance: 135,000 miles (216,000 km) | Action: Inspect | Item: Steering & suspension | Interval in Month(s): 204 | Labor Units: 0.25 | Parts Units: 0 | Drive Type: ALL |
| Description: A vehicle's steering is the collection of components that enable the operator to direct a vehicle in a desired direction. Suspension is the assemblage of joints, links and other components between a vehicle and its wheels. | ||||||
| Distance: 142,500 miles (228,000 km) | Action: Inspect | Item: Exhaust system | Interval in Month(s): 96 | Labor Units: 0.05 | Parts Units: 0 | Drive Type: ALL |
| Description: A system of tubing that routes exhaust gases from the exhaust manifold to the rear of the car and into the air. The exhaust system includes catalytic converters and mufflers that help reduce air and noise pollution generated by an engine. | ||||||
| Distance: 142,500 miles (228,000 km) | Action: Inspect | Item: Steering & suspension | Interval in Month(s): 132 | Labor Units:
0.25 | Parts Units: 0 | Drive Type: ALL |
| Description: A vehicle's steering is the collection of components that enable the operator to direct a vehicle in a desired direction. Suspension is the assemblage of joints, links and other components between a vehicle and its wheels. | ||||||
| Distance: 142,500 miles (228,000 km) | Action: Inspect boots & seals | Item: Drive shaft, pilot bearing & u-joints | Interval in Month(s): 228 | Labor Units: 0.2 | Parts Units: 0 | Drive Type: ALL |
| Description: In a rear- or four-wheel drive vehicle, the drive shaft is a sturdy metal tube with flexible joints on either end that connects the source of power to a differential. The pilot bearing is a bearing press-fit into the rear of the crankshaft that supports the tip of the transmission input shaft. It should be routinely replaced whenever the clutch is replaced as this is when it's most accessible. | ||||||
| Distance: 150,000 miles (240,000 km) | Action: Inspect boots & seals | Item: Drive shaft, pilot bearing & u-joints | Interval in Month(s): 132 | Labor Units: 0.2 | Parts Units: 0 | Drive Type: ALL |
| Description: In a rear- or four-wheel drive vehicle, the drive shaft is a sturdy metal tube with flexible joints on either end that connects the source of power to a differential. The pilot bearing is a bearing press-fit into the rear of the crankshaft that supports the tip of the transmission input shaft. It should be routinely replaced whenever the clutch is replaced as this is when it's most accessible. | ||||||
| Distance: 150,000 miles (240,000 km) | Action: Inspect | Item: Exhaust system | Interval in Month(s): 192 | Labor Units: 0.05 | Parts Units: 0 | Drive Type: ALL |
| Description: A system of tubing that routes exhaust gases from the exhaust manifold to the rear of the car and into the air. The exhaust system includes catalytic converters and mufflers that help reduce air and noise pollution generated by an engine. | ||||||
| Distance: 150,000 miles (240,000 km) | Action: Inspect | Item: Steering & suspension | Interval in Month(s): 228 | Labor Units: 0.25 | Parts Units: 0 | Drive Type: ALL |
| Description: A vehicle's steering is the collection of components that enable the operator to direct a vehicle in a desired direction. Suspension is the assemblage of joints, links and other components between a vehicle and its wheels. | ||||||
| Distance: 150,000 miles (240,000 km) | Action: Replace | Item: Alternator | Interval in Month(s): 168 | Labor Units: 0.2 | Parts Units: 1 | Drive Type: ALL |
| Description: Device that converts mechanical energy to alternating current electrical energy. | ||||||
| Distance: 157,500 miles (252,000 km) | Action: Inspect boots & seals | Item: Drive shaft, pilot bearing & u-joints | Interval in Month(s): 96 | Labor Units: 0.2 | Parts Units: 0 | Drive Type: ALL |
| Description: In a rear- or four-wheel drive vehicle, the drive shaft is a sturdy metal tube with flexible joints on either end that connects the source of power to a differential. The pilot bearing is a bearing press-fit into the rear of the crankshaft that supports the tip of the transmission input shaft. It should be routinely replaced whenever the clutch is replaced as this is when it's most accessible. | ||||||
| Distance: 157,500 miles (252,000 km) | Action: Inspect | Item: Steering & suspension | Interval in Month(s): 180 | Labor Units: 0.25 | Parts Units: 0 | Drive Type: ALL |
| Description: A vehicle's steering is the collection of components that enable the operator to direct a vehicle in a desired direction. Suspension is the assemblage of joints, links and other components between a vehicle and its wheels. | ||||||
| Distance: 157,500 miles (252,000 km) | Action: Inspect | Item: Exhaust system | Interval in Month(s): 228 | Labor Units: 0.05 | Parts Units: 0 | Drive Type: ALL |
| Description: A system of tubing that routes exhaust gases from the exhaust manifold to the rear of the car and into the air. The exhaust system includes catalytic converters and mufflers that help reduce air and noise pollution generated by an engine. | ||||||
| Distance: 165,000 miles (264,000 km) | Action: Inspect | Item: Battery | Interval in Month(s): 12 | Labor Units: 0.1 | Parts Units: 0 | Drive Type: ALL |
| Description: A box containing lead plates filled with a water and acid mixture that stores electricity generated by the alternator. It is the source of power for parts of the car that operate on electricity. | ||||||
| Distance: 165,000 miles (264,000 km) | Action: Inspect | Item: Steering & suspension | Interval in Month(s): 120 | Labor Units: 0.25 | Parts Units: 0 | Drive Type: ALL |
| Description: A vehicle's steering is the collection of components that enable the operator to direct a vehicle in a desired direction. Suspension is the assemblage of joints, links and other components between a vehicle and its wheels. | ||||||
| Distance: 165,000 miles (264,000 km) | Action: Inspect boots & seals | Item: Drive shaft, pilot bearing & u-joints | Interval in Month(s): 192 | Labor Units: 0.2 | Parts Units: 0 | Drive Type: ALL |
| Description: In a rear- or four-wheel drive vehicle, the drive shaft is a sturdy metal tube with flexible joints on either end that connects the source of power to a differential. The pilot bearing is a bearing press-fit into the rear of the crankshaft that supports the tip of the transmission input shaft. It should be routinely replaced whenever the clutch is replaced as this is when it's most accessible. | ||||||
| Distance: 165,000 miles (264,000 km) | Action: Inspect | Item: Exhaust system | Interval in Month(s): 240 | Labor Units: 0.05 | Parts Units: 0 | Drive Type: ALL |
| Description: A system of tubing that routes exhaust gases from the exhaust manifold to the rear of the car and into the air. The exhaust system includes catalytic converters and mufflers that help reduce air and noise pollution generated by an engine. | ||||||
| Distance: 172,500 miles (276,000 km) | Action: Inspect | Item: Steering & suspension | Interval in Month(s): 108 | Labor Units: 0.25 | Parts Units: 0 | Drive Type: ALL |
| Description: A vehicle's steering is the collection of components that enable the operator to direct a vehicle in a desired direction. Suspension is the assemblage of joints, links and other components between a vehicle and its wheels. | ||||||
| Distance: 172,500 miles (276,000 km) | Action: Inspect | Item: Exhaust system | Interval in
Month(s): 144 | Labor Units: 0.05 | Parts Units: 0 | Drive Type: ALL |
| Description: A system of tubing that routes exhaust gases from the exhaust manifold to the rear of the car and into the air. The exhaust system includes catalytic converters and mufflers that help reduce air and noise pollution generated by an engine. | ||||||
| Distance: 172,500 miles (276,000 km) | Action: Inspect boots & seals | Item: Drive shaft, pilot bearing & u-joints | Interval in Month(s): 216 | Labor Units: 0.2 | Parts Units: 0 | Drive Type: ALL |
| Description: In a rear- or four-wheel drive vehicle, the drive shaft is a sturdy metal tube with flexible joints on either end that connects the source of power to a differential. The pilot bearing is a bearing press-fit into the rear of the crankshaft that supports the tip of the transmission input shaft. It should be routinely replaced whenever the clutch is replaced as this is when it's most accessible. | ||||||
| Distance: 187,500 miles (300,000 km) | Action: Inspect | Item: Steering & suspension | Interval in Month(s): 192 | Labor Units: 0.25 | Parts Units: 0 | Drive Type: ALL |
| Description: A vehicle's steering is the collection of components that enable the operator to direct a vehicle in a desired direction. Suspension is the assemblage of joints, links and other components between a vehicle and its wheels. | ||||||
| Distance: 187,500 miles (300,000 km) | Action: Inspect boots & seals | Item: Drive shaft, pilot bearing & u-joints | Interval in Month(s): 204 | Labor Units: 0.2 | Parts Units: 0 | Drive Type: ALL |
| Description: In a rear- or four-wheel drive vehicle, the drive shaft is a sturdy metal tube with flexible joints on either end that connects the source of power to a differential. The pilot bearing is a bearing press-fit into the rear of the crankshaft that supports the tip of the transmission input shaft. It should be routinely replaced whenever the clutch is replaced as this is when it's most accessible. | ||||||
| Distance: 187,500 miles (300,000 km) | Action: Inspect | Item: Exhaust system | Interval in Month(s): 216 | Labor Units: 0.05 | Parts Units: 0 | Drive Type: ALL |
| Description: A system of tubing that routes exhaust gases from the exhaust manifold to the rear of the car and into the air. The exhaust system includes catalytic converters and mufflers that help reduce air and noise pollution generated by an engine. | ||||||
| Distance: 195,000 miles (312,000 km) | Action: Inspect | Item: Battery | Interval in Month(s): 12 | Labor Units: 0.1 | Parts Units: 0 | Drive Type: ALL |
| Description: A box containing lead plates filled with a water and acid mixture that stores electricity generated by the alternator. It is the source of power for parts of the car that operate on electricity. | ||||||
| Distance: 195,000 miles (312,000 km) | Action: Inspect | Item: Steering & suspension | Interval in Month(s): 96 | Labor Units:
0.25 | Parts Units: 0 | Drive Type: ALL |
| Description: A vehicle's steering is the collection of components that enable the operator to direct a vehicle in a desired direction. Suspension is the assemblage of joints, links and other components between a vehicle and its wheels. | ||||||
| Distance: 195,000 miles (312,000 km) | Action: Inspect boots & seals | Item: Drive shaft, pilot bearing & u-joints | Interval in Month(s): 168 | Labor Units: 0.2 | Parts Units: 0 | Drive Type: ALL |
| Description: In a rear- or four-wheel drive vehicle, the drive shaft is a sturdy metal tube with flexible joints on either end that connects the source of power to a differential. The pilot bearing is a bearing press-fit into the rear of the crankshaft that supports the tip of the transmission input shaft. It should be routinely replaced whenever the clutch is replaced as this is when it's most accessible. | ||||||
| Distance: 195,000 miles (312,000 km) | Action: Inspect | Item: Exhaust system | Interval in Month(s): 216 | Labor Units: 0.05 | Parts Units: 0 | Drive Type: ALL |
| Description: A system of tubing that routes exhaust gases from the exhaust manifold to the rear of the car and into the air. The exhaust system includes catalytic converters and mufflers that help reduce air and noise pollution generated by an engine. | ||||||
| Distance: 202,500 miles (324,000 km) | Action: Inspect boots & seals | Item: Drive shaft, pilot bearing & u-joints | Interval in
Month(s): 132 | Labor Units: 0.2 | Parts Units: 0 | Drive Type: ALL |
| Description: In a rear- or four-wheel drive vehicle, the drive shaft is a sturdy metal tube with flexible joints on either end that connects the source of power to a differential. The pilot bearing is a bearing press-fit into the rear of the crankshaft that supports the tip of the transmission input shaft. It should be routinely replaced whenever the clutch is replaced as this is when it's most accessible. | ||||||
| Distance: 202,500 miles (324,000 km) | Action: Inspect | Item: Steering & suspension | Interval in Month(s): 228 | Labor Units: 0.25 | Parts Units: 0 | Drive Type: ALL |
| Description: A vehicle's steering is the collection of components that enable the operator to direct a vehicle in a desired direction. Suspension is the assemblage of joints, links and other components between a vehicle and its wheels. | ||||||
| Distance: 202,500 miles (324,000 km) | Action: Inspect | Item: Exhaust system | Interval in Month(s): 240 | Labor Units: 0.05 | Parts Units: 0 | Drive Type: ALL |
| Description: A system of tubing that routes exhaust gases from the exhaust manifold to the rear of the car and into the air. The exhaust system includes catalytic converters and mufflers that help reduce air and noise pollution generated by an engine. | ||||||
| Distance: 210,000 miles (336,000 km) | Action: Inspect boots & seals | Item: Drive shaft, pilot bearing & u-joints | Interval in
Month(s): 156 | Labor Units: 0.2 | Parts Units: 0 | Drive Type: ALL |
| Description: In a rear- or four-wheel drive vehicle, the drive shaft is a sturdy metal tube with flexible joints on either end that connects the source of power to a differential. The pilot bearing is a bearing press-fit into the rear of the crankshaft that supports the tip of the transmission input shaft. It should be routinely replaced whenever the clutch is replaced as this is when it's most accessible. | ||||||
| Distance: 210,000 miles (336,000 km) | Action: Inspect | Item: Exhaust system | Interval in Month(s): 192 | Labor Units: 0.05 | Parts Units: 0 | Drive Type: ALL |
| Description: A system of tubing that routes exhaust gases from the exhaust manifold to the rear of the car and into the air. The exhaust system includes catalytic converters and mufflers that help reduce air and noise pollution generated by an engine. | ||||||
| Distance: 210,000 miles (336,000 km) | Action: Inspect | Item: Steering & suspension | Interval in Month(s): 240 | Labor Units: 0.25 | Parts Units: 0 | Drive Type: ALL |
| Description: A vehicle's steering is the collection of components that enable the operator to direct a vehicle in a desired direction. Suspension is the assemblage of joints, links and other components between a vehicle and its wheels. | ||||||
| Distance: 217,500 miles (348,000 km) | Action: Inspect boots & seals | Item: Drive shaft, pilot bearing & u-joints | Interval in
Month(s): 204 | Labor Units: 0.2 | Parts Units: 0 | Drive Type: ALL |
| Description: In a rear- or four-wheel drive vehicle, the drive shaft is a sturdy metal tube with flexible joints on either end that connects the source of power to a differential. The pilot bearing is a bearing press-fit into the rear of the crankshaft that supports the tip of the transmission input shaft. It should be routinely replaced whenever the clutch is replaced as this is when it's most accessible. | ||||||
| Distance: 217,500 miles (348,000 km) | Action: Inspect | Item: Steering & suspension | Interval in Month(s): 216 | Labor Units: 0.25 | Parts Units: 0 | Drive Type: ALL |
| Description: A vehicle's steering is the collection of components that enable the operator to direct a vehicle in a desired direction. Suspension is the assemblage of joints, links and other components between a vehicle and its wheels. | ||||||
| Distance: 217,500 miles (348,000 km) | Action: Inspect | Item: Exhaust system | Interval in Month(s): 228 | Labor Units: 0.05 | Parts Units: 0 | Drive Type: ALL |
| Description: A system of tubing that routes exhaust gases from the exhaust manifold to the rear of the car and into the air. The exhaust system includes catalytic converters and mufflers that help reduce air and noise pollution generated by an engine. | ||||||
| Distance: 225,000 miles (360,000 km) | Action: Inspect | Item: Battery | Interval in Month(s): 12 | Labor Units:
0.1 | Parts Units: 0 | Drive Type: ALL |
| Description: A box containing lead plates filled with a water and acid mixture that stores electricity generated by the alternator. It is the source of power for parts of the car that operate on electricity. | ||||||
| Distance: 225,000 miles (360,000 km) | Action: Inspect | Item: Exhaust system | Interval in Month(s): 144 | Labor Units: 0.05 | Parts Units: 0 | Drive Type: ALL |
| Description: A system of tubing that routes exhaust gases from the exhaust manifold to the rear of the car and into the air. The exhaust system includes catalytic converters and mufflers that help reduce air and noise pollution generated by an engine. | ||||||
| Distance:
225,000 miles (360,000 km) | Action: Inspect | Item: Steering & suspension | Interval in Month(s): 216 | Labor Units: 0.25 | Parts Units: 0 | Drive Type: ALL |
| Description: A vehicle's steering is the collection of components that enable the operator to direct a vehicle in a desired direction. Suspension is the assemblage of joints, links and other components between a vehicle and its wheels. | ||||||
| Distance: 225,000 miles (360,000 km) | Action: Inspect boots & seals | Item: Drive shaft, pilot bearing & u-joints | Interval in Month(s): 216 | Labor Units: 0.2 | Parts Units: 0 | Drive Type: ALL |
| Description: In a rear- or four-wheel drive vehicle, the drive shaft is a sturdy metal tube with flexible joints on either end that connects the source of power to a differential. The pilot bearing is a bearing press-fit into the rear of the crankshaft that supports the tip of the transmission input shaft. It should be routinely replaced whenever the clutch is replaced as this is when it's most accessible. | ||||||
| Distance: 232,500 miles (372,000 km) | Action: Inspect | Item: Exhaust system | Interval in Month(s): 108 | Labor Units: 0.05 | Parts Units: 0 | Drive Type: ALL |
| Description: A system of tubing that routes exhaust gases from the exhaust manifold to the rear of the car and into the air. The exhaust system includes catalytic converters and mufflers that help reduce air and noise pollution generated by an engine. | ||||||
| Distance: 232,500 miles (372,000 km) | Action: Inspect | Item: Steering & suspension | Interval in Month(s): 144 | Labor Units: 0.25 | Parts Units: 0 | Drive Type: ALL |
| Description: A vehicle's steering is the collection of components that enable the operator to direct a vehicle in a desired direction. Suspension is the assemblage of joints, links and other components between a vehicle and its wheels. | ||||||
| Distance: 232,500 miles (372,000 km) | Action: Inspect boots & seals | Item: Drive shaft, pilot bearing & u-joints | Interval in Month(s): 144 | Labor Units: 0.2 | Parts Units: 0 | Drive Type: ALL |
| Description: In a rear- or four-wheel drive vehicle, the drive shaft is a sturdy metal tube with flexible joints on either end that connects the source of power to a differential. The pilot bearing is a bearing press-fit into the rear of the crankshaft that supports the tip of the transmission input shaft. It should be routinely replaced whenever the clutch is replaced as this is when it's most accessible. | ||||||
| Distance: 247,500 miles (396,000 km) | Action: Inspect boots & seals | Item: Drive shaft, pilot bearing & u-joints | Interval in Month(s): 108 | Labor Units: 0.2 | Parts Units: 0 | Drive Type: ALL |
| Description: In a rear- or four-wheel drive vehicle, the drive shaft is a sturdy metal tube with flexible joints on either end that connects the source of power to a differential. The pilot bearing is a bearing press-fit into the rear of the crankshaft that supports the tip of the transmission input shaft. It should be routinely replaced whenever the clutch is replaced as this is when it's most accessible. | ||||||
| Distance: 247,500 miles (396,000 km) | Action: Inspect | Item: Steering & suspension | Interval in Month(s): 120 | Labor Units: 0.25 | Parts Units: 0 | Drive Type: ALL |
| Description: A vehicle's steering is the collection of components that enable the operator to direct a vehicle in a desired direction. Suspension is the assemblage of joints, links and other components between a vehicle and its wheels. | ||||||
| Distance: 247,500 miles (396,000 km) | Action: Inspect | Item: Exhaust system | Interval in Month(s): 132 | Labor Units:
0.05 | Parts Units: 0 | Drive Type: ALL |
| Description: A system of tubing that routes exhaust gases from the exhaust manifold to the rear of the car and into the air. The exhaust system includes catalytic converters and mufflers that help reduce air and noise pollution generated by an engine. | ||||||
| Distance: 255,000 miles (408,000 km) | Action: Inspect | Item: Battery | Interval in Month(s): 12 | Labor Units: 0.1 | Parts Units: 0 | Drive Type: ALL |
| Description: A box containing lead plates filled with a water and acid mixture that stores electricity generated by the alternator. It is the source of power for parts of the car that operate on electricity. | ||||||
| Distance: 255,000 miles (408,000 km) | Action: Inspect boots & seals | Item: Drive shaft, pilot bearing & u-joints | Interval in Month(s): 108 | Labor Units: 0.2 | Parts Units: 0 | Drive Type: ALL |
| Description: In a rear- or four-wheel drive vehicle, the drive shaft is a sturdy metal tube with flexible joints on either end that connects the source of power to a differential. The pilot bearing is a bearing press-fit into the rear of the crankshaft that supports the tip of the transmission input shaft. It should be routinely replaced whenever the clutch is replaced as this is when it's most accessible. | ||||||
| Distance: 255,000 miles (408,000 km) | Action: Inspect | Item: Steering & suspension | Interval in Month(s): 120 | Labor Units: 0.25 | Parts Units:
0 | Drive Type: ALL |
| Description: A vehicle's steering is the collection of components that enable the operator to direct a vehicle in a desired direction. Suspension is the assemblage of joints, links and other components between a vehicle and its wheels. | ||||||
| Distance: 255,000 miles (408,000 km) | Action: Inspect | Item: Exhaust system | Interval in Month(s): 132 | Labor Units: 0.05 | Parts Units: 0 | Drive Type: ALL |
| Description: A system of tubing that routes exhaust gases from the exhaust manifold to the rear of the car and into the air. The exhaust system includes catalytic converters and mufflers that help reduce air and noise pollution generated by an engine. | ||||||
| Distance:
262,500 miles (420,000 km) | Action: Inspect boots & seals | Item: Drive shaft, pilot bearing & u-joints | Interval in Month(s): 108 | Labor Units: 0.2 | Parts Units: 0 | Drive Type: ALL |
| Description: In a rear- or four-wheel drive vehicle, the drive shaft is a sturdy metal tube with flexible joints on either end that connects the source of power to a differential. The pilot bearing is a bearing press-fit into the rear of the crankshaft that supports the tip of the transmission input shaft. It should be routinely replaced whenever the clutch is replaced as this is when it's most accessible. | ||||||
| Distance: 262,500 miles (420,000 km) | Action: Inspect | Item: Steering & suspension | Interval in Month(s): 120 | Labor Units: 0.25 | Parts
Units: 0 | Drive Type: ALL |
| Description: A vehicle's steering is the collection of components that enable the operator to direct a vehicle in a desired direction. Suspension is the assemblage of joints, links and other components between a vehicle and its wheels. | ||||||
| Distance: 262,500 miles (420,000 km) | Action: Inspect | Item: Exhaust system | Interval in Month(s): 132 | Labor Units: 0.05 | Parts Units: 0 | Drive Type: ALL |
| Description: A system of tubing that routes exhaust gases from the exhaust manifold to the rear of the car and into the air. The exhaust system includes catalytic converters and mufflers that help reduce air and noise pollution generated by an engine. | ||||||
| Distance:
270,000 miles (432,000 km) | Action: Inspect boots & seals | Item: Drive shaft, pilot bearing & u-joints | Interval in Month(s): 108 | Labor Units: 0.2 | Parts Units: 0 | Drive Type: ALL |
| Description: In a rear- or four-wheel drive vehicle, the drive shaft is a sturdy metal tube with flexible joints on either end that connects the source of power to a differential. The pilot bearing is a bearing press-fit into the rear of the crankshaft that supports the tip of the transmission input shaft. It should be routinely replaced whenever the clutch is replaced as this is when it's most accessible. | ||||||
| Distance: 270,000 miles (432,000 km) | Action: Inspect | Item: Steering & suspension | Interval in Month(s): 120 | Labor Units: 0.25 | Parts
Units: 0 | Drive Type: ALL |
| Description: A vehicle's steering is the collection of components that enable the operator to direct a vehicle in a desired direction. Suspension is the assemblage of joints, links and other components between a vehicle and its wheels. | ||||||
| Distance: 270,000 miles (432,000 km) | Action: Inspect | Item: Exhaust system | Interval in Month(s): 132 | Labor Units: 0.05 | Parts Units: 0 | Drive Type: ALL |
| Description: A system of tubing that routes exhaust gases from the exhaust manifold to the rear of the car and into the air. The exhaust system includes catalytic converters and mufflers that help reduce air and noise pollution generated by an engine. | ||||||
| Distance:
277,500 miles (444,000 km) | Action: Inspect boots & seals | Item: Drive shaft, pilot bearing & u-joints | Interval in Month(s): 108 | Labor Units: 0.2 | Parts Units: 0 | Drive Type: ALL |
| Description: In a rear- or four-wheel drive vehicle, the drive shaft is a sturdy metal tube with flexible joints on either end that connects the source of power to a differential. The pilot bearing is a bearing press-fit into the rear of the crankshaft that supports the tip of the transmission input shaft. It should be routinely replaced whenever the clutch is replaced as this is when it's most accessible. | ||||||
| Distance: 277,500 miles (444,000 km) | Action: Inspect | Item: Steering & suspension | Interval in Month(s): 120 | Labor Units: 0.25 | Parts
Units: 0 | Drive Type: ALL |
| Description: A vehicle's steering is the collection of components that enable the operator to direct a vehicle in a desired direction. Suspension is the assemblage of joints, links and other components between a vehicle and its wheels. | ||||||
| Distance: 277,500 miles (444,000 km) | Action: Inspect | Item: Exhaust system | Interval in Month(s): 132 | Labor Units: 0.05 | Parts Units: 0 | Drive Type: ALL |
| Description: A system of tubing that routes exhaust gases from the exhaust manifold to the rear of the car and into the air. The exhaust system includes catalytic converters and mufflers that help reduce air and noise pollution generated by an engine. | ||||||
| Distance:
285,000 miles (456,000 km) | Action: Inspect | Item: Battery | Interval in Month(s): 12 | Labor Units: 0.1 | Parts Units: 0 | Drive Type: ALL |
| Description: A box containing lead plates filled with a water and acid mixture that stores electricity generated by the alternator. It is the source of power for parts of the car that operate on electricity. | ||||||
| Distance: 285,000 miles (456,000 km) | Action: Inspect boots & seals | Item: Drive shaft, pilot bearing & u-joints | Interval in Month(s): 108 | Labor Units: 0.2 | Parts Units: 0 | Drive Type: ALL |
| Description: In a rear- or four-wheel drive vehicle, the drive shaft is a sturdy metal tube with flexible joints on either end that connects the source of power to a differential. The pilot bearing is a bearing press-fit into the rear of the crankshaft that supports the tip of the transmission input shaft. It should be routinely replaced whenever the clutch is replaced as this is when it's most accessible. | ||||||
| Distance: 285,000 miles (456,000 km) | Action: Inspect | Item: Steering & suspension | Interval in Month(s): 120 | Labor Units: 0.25 | Parts Units: 0 | Drive Type: ALL |
| Description: A vehicle's steering is the collection of components that enable the operator to direct a vehicle in a desired direction. Suspension is the assemblage of joints, links and other components between a vehicle and its wheels. | ||||||
| Distance: 285,000 miles (456,000 km) | Action:
Inspect | Item: Exhaust system | Interval in Month(s): 132 | Labor Units: 0.05 | Parts Units: 0 | Drive Type: ALL |
| Description: A system of tubing that routes exhaust gases from the exhaust manifold to the rear of the car and into the air. The exhaust system includes catalytic converters and mufflers that help reduce air and noise pollution generated by an engine. | ||||||
| Distance: 292,500 miles (468,000 km) | Action: Inspect boots & seals | Item: Drive shaft, pilot bearing & u-joints | Interval in Month(s): 108 | Labor Units: 0.2 | Parts Units: 0 | Drive Type: ALL |
| Description: In a rear- or four-wheel drive vehicle, the drive shaft is a sturdy metal tube with flexible joints on either end that connects the source of power to a differential. The pilot bearing is a bearing press-fit into the rear of the crankshaft that supports the tip of the transmission input shaft. It should be routinely replaced whenever the clutch is replaced as this is when it's most accessible. | ||||||
| Distance: 292,500 miles (468,000 km) | Action: Inspect | Item: Steering & suspension | Interval in Month(s): 120 | Labor Units: 0.25 | Parts Units: 0 | Drive Type: ALL |
| Description: A vehicle's steering is the collection of components that enable the operator to direct a vehicle in a desired direction. Suspension is the assemblage of joints, links and other components between a vehicle and its wheels. | ||||||
| Distance: 292,500 miles (468,000 km) | Action:
Inspect | Item: Exhaust system | Interval in Month(s): 132 | Labor Units: 0.05 | Parts Units: 0 | Drive Type: ALL |
| Description: A system of tubing that routes exhaust gases from the exhaust manifold to the rear of the car and into the air. The exhaust system includes catalytic converters and mufflers that help reduce air and noise pollution generated by an engine. | ||||||
Canada
United States